Clean and Oil
Stripping gun, cleaning all parts, checking for wear, making suggestions to a customer of services needed to put in A-1 condition.
- Handgun $65
- Rifle & AR/AK Pistol $130
Sonic Cleaning
- Handgun $95
- Rifle & AR/AK Pistol $160
Rebluing
- Abrasive / Media Blast / Wire Wheel (Matte Finish) $250
- Hangun Deluxe Finish $300
Same as above followed with #240 and $400 grit polish with all screw holes and corners protected and square
- Rifle & AR/AK Pistol $400
Same as above followed with #240 and $400 grit polish with all screw holes and corners protected and square
- Slow Rust Bluing $250-$650
- Cerakote $200
- Bead, Sandblast or Wire Brush Stainless Steel $140
Sight Work
- Sight In Customer Gun $75
Does not include cost of ammo, targets, etc.
- Bore Sight Customer Gun $25
- Pattern Shotgun $25
Does not include cost of ammo, targets, etc.
- Install Insert In Pistol Sight $50
- Install Front / Mid-Rib Shotgun Bead $65
- Install Receiver Sights $45
Gun Drilled and Tapped
- Scope Mounting $50
Gun Drilled and Tapped
General Barrel, Action & Rifle Work
- Check Headspace $65
- Remove Stuck Fired Case From Chamber $50
- Remove Live Round From Chamber $130
- Remove Obstruction From Bore Hourly Rate
- Remove Fouling From Barrel Hourly Rate + Materials
- Cut and Crown Barrel $130
- Install Pre-Threaded and Chambered Barrel $130
Not including polishing and bluing
- Install Spring Hourly Rate
- Install Muzzle Brake (Threaded Barrel) $65
- Install Barrel and Swivel Hourly Rate
Safeties Installation
- Dakota, Gentry, Mod 70 Type Safety With Shroud $175
- Mark II / Beuhlertype $100
- Chapman Swing Safety Lever $135
Triggers (Installation / Adjustment)
- Shilen, Timney, Dayton-Traister, Moyer Type $90
- Double Set $250
- Single Set $140
Handgun Work
- Chamfer Revolver Barrel $45
- Chamfer Revolver Cylinder $80
- Revolver Action Job $160
Clean, smooth action, not including replacement of parts
- Rebarrel Revolver $160
Remove old barrel, replace with new factory barrel, labor only
- Straighten Crane On Revolver $80
- Install Crane On Revolver $80
- Install Crane Lock $50
- Remove / Modify Revolver Hammer Spur $80
- Convert Revolver From Square To Round Butt $120
- Semi-Auto Pistol Action Job $220
Clean, smooth action, not including any parts
- Tighten Slide of 1911 Auto $175
- Fit Barrel To 1911 Semi-Auto (Non-Ramped) $150
Not Including Barrel
- Fit Barrel To 1911 Semi-Auto (Ramped) $175
Not Including Barrel
- Fit & Install Barrel Bushing On 1911 Semi-Auto $120
Does not include cost of bushing
- Bevel Magazinewell of 1911 Semi-Auto $80
- Open & Modify Ejection Port Of 1911 Slide $120
- Throat, Polish Barrel & Feed Ramp Of 1911 $100
- Fit New Trigger To 1911 $80
Does not include cost of trigger
- Fit New Hammer to 1911 $100
Does not include cost of hammer
- Install Fiber Optic Front Sight $45
Existing dovetail w/o cost of sight
- Install Rear Sight $45
Existing dovetail w/o cost of sight
- Dehorn & Break Edges For Carry $75
Does not include re-finish
- Install Semi-Auto Compensator $250
AR-15/10 Work
Does not include cost of parts.
- Maintenance Cleaning $65
Includes complete disassembly, clean, safety check, oil, and reassemble
- Maintenance Rebuild $150
Includes new spring & new gas rings added to the maintenance cleaning
- Install Aftermarket Trigger $80
- Install Aftermarket Forend / Free-Float $130
- Assemble Complete Upper $85
- Assemble Complete Lower $85
- Assemble Complete Rifle $150
- Install Flash Hider On Pre-Threaded Barrel $35
- Install Or Replace Gas Block $65
- Install Or Replace AR Barrel $80
- Install Or Replace Butt Stock & Buffer Tube $35